Previously, I had not experimented with rifle magazines ‘jungle clipped’ together. As my gunsmith said, “I’ve haven’t yet had to shoot anything more than 30 times”. A quick search of the interwebs quickly found apocryphal stories of jungle clipped ammo where recoil caused the spare (non-seated) magazine to eject live rounds every time the gun fired, leaving the hapless shooter trying to reload with a mostly empty second mag. Which I suppose could happen… maybe…
Still, it’s a gun accessory I wanted to investigate (and seemingly a popular one for all the versions available: Mag Cinch, Blackhawk?, Command Arms, Springer Precision, Mako Group, etc.) Also, with the AR15 being the ‘Mr. Potato Head’ of firearms, isn’t it incumbent upon AR owners to try as many accessories as possible?
The Mag Cinch by Buffer Tech isn’t the original jungle clip (I believe that title belongs to duct tape) but they do have an innovative, simple and yet solid method of securing the mags. Reading the instructions left me with a fair understanding of how to attach them but there weren’t any pics (not even at Buffer Tech’s website), something my right brain appreciates. Another search of the world wide tubes did not reveal an instructable-type pictorial, which sounded like a waiting blog entry to me. Thus I present to you: “How to Install a Mag Cinch”
I purchased the model for 30 round AR15 magazines. It comes with two cinches that each look like this:
Note #1: The final step of securing the Mag Cinch involves trimming off the excess nylon webbing so getting it right the first time is in your best interests. Buffer Tech sells replacement straps for $1.25
Note #2: About the first thing thing I realized when trying to take the pictures of the process was that black brackets with black webbing on a black magazine don’t show detail very well. However, I found a solution…
Yes, it’s Toxic Green nylon webbing from a local fabric store. I bought a yard and cut it in half with a hot knife (Box knife heated by propane torch) to prevent fraying. Using a leather punch, I made a hole in the center of each half and Ta-Dah! –> replacement straps. The selection at the fabric store allows for a wide range of choices like: tan, purple, florescent pink, black, safety orange, blue camo, rainbow (not that there’s anything wrong with that) or even Ted Nugent-approved zebra stripes.
Let’s Begin. Here are the instructions from Buffer Tech [mostly verbatim with some added commentary]:
WARNING! Important: read instructions carefully before attempting to install. Test completed assembly in unloaded firearm to insure proper clearance prior to use.
1) Adjust screw out fully, screw should be [sic] barely engage threads.
2) Place Mag Cinch unit around magazines, making sure that the large part of assembly is on the front of the magazines. Stagger magazines so that the right one is about 1.5 inches lower than the left. This cinch will sit at the bottom edge of the left magazine.
3) Pull ends of webbing tight. Use needle nose pliers to twist ends tight. It is critical that webbing is tightly holding magazines prior to step 4.
4) Tighten screw until Mag Cinch is holding magazines snugly.
5) Repeat steps 1 – 4 with second Mag Cinch. Adjust this unit so that it sets atop the first unit.
6) Insert magazine assembly into unloaded firearm and adjust fit to suit your needs. Make sure you can operate charging handle, ejection port cover, safeties and other operation features.
[*This is a must; the recommended 1.5 inch offset was too much for my setup and would have impinged on the knurled screw for my Holo Sight]
7) Tighten both screws until the magazine is firmly held in place by the webbing.
8 ) After you are sure that the unit is adjusted, cut off excess webbing. Exposed webbing can be sealed with a lighter or match. [*Or use hot knife to cut and seal the ends at the same time; you might want to put a piece of cardboard over the strapping that you don't want to cut to protect it during this step.]
Afterward it should look like this:
1) The Mag Cinch holds the magazines very securely. There is no movement at all. If forced, I almost think that the mags would give way before the cinch would.
2) The overall result is fairly large – not something that is conducive to putting in a magazine pouch. Methods of comfortably slinging the firearm with cinched mags are reduced due to the bulk.
3) While I haven’t had the chance yet to shoot with the cinched mags to see if the ‘spare mag’ ejects live rounds during recoil (unlikely), using the MagPul P-Mag dust cover on the left magazine would certainly prevent that from happening.
4) From a practical standpoint, I’m not completely sold on ‘jungle clipping’ mags unless using them in a war zone or for action matches (3 Gun, etc.). However, if your particular storage requirements dictate having an unloaded rifle the Mag Cinch might offer a solution. In that case, you could leave the right side magazine empty yet seated in the rifle’s mag well but also have a full magazine less than an inch away, ready to go. I admit this defies most logic [After all, who wants an empty mag on a fighting gun?] but may allow greater readiness in situations where such policies / laws exist.
5) I need a better camera and light box setup
6) I’m pretty sure that my ‘Cinched magazines won’t be lost for lack of visibility or be confused with anyone else’s.