Is 15 Inches Too Long?

Perhaps. More on that later.

After talking with the guys at AP Industries about their carbon fiber handguards, I ordered one for a ‘special project’.  The 15 inch ‘Tactical’ model to be exact, because I want the full length top rail for mounting iron sights.  The Tactical models also come with a couple of 2″ picatinny rails that can be mounted to any of the vents in the handguard.  Those will be put to use later.

New 15″ Tactical Handguard from AP Custom USA.
[Note: strap wrench and action figure NOT required for installation]

I had not attempted this type of project before [I’m not a gunsmith] and because I wanted to learn how to change out handguards / build AR upper receivers, I set about collecting the necessary tools.  The project upper was sporting a Hogue free float tube so I needed a strap wrench to remove it.  The upper receiver vise block I chose is by Wheeler Engineering and includes a very clever gas port alignment tool.  To install the new AP Customs handguard I needed a barrel nut wrench and a barrel nut.  Also required, but thankfully already owned, are a T15 Torx driver, a 1/2″ socket wrench handle, Blue Loctite, and a big honking vise.

Disclaimer: I am not a gunsmith.  This article does not constitute instruction. I’m not responsible for damage to you or your gun if you don’t seek out qualified instruction elsewhere.  I’ll leave it up to you to figure out how to remove muzzle devices, gas blocks, gas tubes, etc.

So, to the part where I remove the Hogue handguard (except that I didn’t get a picture of it in the vise)

Imagine this clamped in a vise… [Gas port alignment rod removed for illustrative purposes]

There. Done.

A couple of neat features of the AP Customs handguards are how light they are and how brilliant the attachment system is. APC designed a cup and a flange that ‘sandwich’ the barrel nut and ensure that when the gas tube port is aligned, the handguard (and therefore the top rail) is too.  Here’s how the parts are ordered: [click images to enlarge]

Parts of the AP Custom handguard attachment system shown aligned in ‘exploded’ view. Milspec barrel nut is NOT included with handguard.

These forum posts have more pictures if you are curious.  I cinched everything up using the highly technical method of turning the barrel nut to ‘hand tight’ and then using the barrel nut wrench to tighten it just enough until the nearest barrel nut notch aligned with the gas tube port.  No torque wrench needed.

As for weight savings, the Hogue midlength tube, with its integral barrel nut, weighs 9.9 ounces on my postal scale. The APC handguard parts and barrel nut combine to weigh 10.5 ounces.  That’s 6 inches more real estate to hold onto, plus a rail to attach sights to for only 0.6 ounces added.  Of course, adding additional rails for lights, VFG’s, etc will cause the weigh to stack up, as will adding those devices but that’s for each to decide on their own.

So how did it turn out?  Tune in Monday for the reveal!

Tactical Wifi Cantenna

h/t to EverydayNoDaysOff

Cantenna:
A `cantenna` is a directional waveguide antenna for long-range Wi-Fi used to increase the range of (or snoop on) a wireless network. Originally built using a Pringles potato chip can, a cantenna can be constructed quickly, easily, and inexpensively using readily obtained materials:

Tac·ti·cal
adjective /ˈtaktikəl/

• Of, relating to, or constituting actions carefully planned to gain a specific military end
  • – as a tactical officer in the field he had no equal
• (of bombing or weapons) Done or for use in immediate support of military or naval operations
• (of a person or their actions) Showing adroit planning; aiming at an end beyond the immediate action
• [Something that is black in color and often adorned with picatinny rails]

Tactical Cantenna (Blogpost with Build Instructions)

Tactical Cantenna

Neat.

Also, far more useful than the Tactical Vuvuzela.

Tactical Vuvuzela

Tactical Seat Covers – Seen at Dallas Tea Party

Check these out!

The latest in tactical innovation.

Looks like a custom base of PALS webbing with attached MOLLE gear.  [What? No Camelbak?]

All in all: Nicely done, sir.